Sterling Silver Crescent and Bead Earrings
Supplies Desired
3" 4 x 1 mm sterling silver rectangle wire
20-just one 'Λ* head pins
Two turquoise disc beads
A person Vi* 1.7 mm black hollow rubber tube
Two sterling silver ear wires
What suggestions would you give you a commencing artist?
“Do Anything you love. Discover distinct media. Offer with a selective, confined, foundation in the beginning to view what will work or what would not work for you before you jump into A significant outlay of money and effort.*
-Sally J. Phillips Jewelry Designer
Instruments Wanted
Ruler
Marker
Jeweler's observed or tin snips Protection Eyeglasses Hard, flat surface Awl
Hammer /is" drill bit
Hand held rotary Instrument, flex shaft, or drill press File
Fantastic grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Scissors
Wire cutters or tin snips Round nose pliers
1.Make use of the ruler to evaluate and mark two one Vi’ items of four x one mm rectangle sterling silver wire.
2Using a jeweler's observed or tin snips, Slice the four x one mm rectangle sterling silver wire into two one Vi’ lengths.
three.File Each individual close of the 1Vi" rectangle wire pieces to remove any burs or rough edges.
If desired, You should use the file to round the ends from the rectangle wire pieces. Use a good grit sanding pad to go more than the realm where you have filed to easy the edges and remove any file marks.
4.Use the ruler to measure and mark /*." from one end of the 1 Vi’ pieces of rectangle wire and put a mark in the middle of your wire. This is when you can drill the holes to slip The pinnacle pins by.
five.Place with your basic safety glasses!!! Spot the 1 Vi" rectangle wire pieces onto a hard, flat surface. Put The purpose with the awl to the mark you designed Vm,' from just one conclude on the rectangle wire items, and firmly strike when on the very best from the awl with a hammer. This will make a pilot gap for drilling holes into your rectangle wire.
Sterling Silver Crescent and Bead Earrings
Chapter five
six.Utilizing a /is" drill bit. drill holes into a single finish of the rectangle wire pieces which has a handheld rotary Software, flex shaft, or drill push (even though nevertheless sporting your safety glasses!).
seven.Make use of the file or wonderful grit sanding pad to eradicate any burs or rough edges left from drilling holes into Mens Ring your rectangle wire parts.
eight.Curve the two 1W pieces of rectangle wire right into a “C" condition utilizing a ring mandrel and rawhide mallet. If you do not have a ring mandrel and rawhide mallet, use two set of chain nose pliers. Keeping just one set of pliers in Every hand, grasp Every finish of the one Vi* rectangle wire piece Along with the pliers and Carefully bend the rectangle wire into a “C* shape. Compare both of those on the C-shaped rectangle wire pieces and adjust the curves mens ring so that they're related in si2e. Set these aside.
nine.Make use of the ruler to measure and mark the rubber tube into four equivalent parts measuring Vm’ Just about every. Use Mens Ring scissors to cut the rubber tube.
10.Put the turquoise disc bead on to The top mens ring pin and add a person V·' bit of the rubber tube, spot the head pin Mens Ring in the gap inside the C-shaped rectangle wire, after which you can insert another V«" piece of rubber tube.
thirteen. Maintain the head pin While using the bead, rubber tube, plus the rectangle wire on it in one hand with the wire that you choose to bent pointing towards you. Using the spherical nose pliers, grip the tip of the head pin wire that may be pointing towards you and roll it far from you (think of turning the ignition essential to begin your car). Launch the pliers from The top pin wire.
At this point, the opening from the loop at the very best of the head pin wire really should nevertheless be big more than enough to slip the ear wire on. After you insert the ear wire, make use of the round nose pliers to grasp the loop of The top pin wire and roll it closed. You may use the spherical nose or chain nose pliers to adjust The form with the loop at the highest of the head pin if you need to.
eleven. Use the ruler to evaluate and mark /(.’ over the best bit of the hollow rubber tube. Using the wire cutters or tin snips, Slash The top pin wire Yu.’ above the best on the hollow rubber tube.
twelve. Make use of the chain nose pliers to bend the head pin wire close to the top with the rubber tube at a ninety-degree angle.
fourteen. Repeat these measures for the 2nd earring.